Welding Aluminum TIG vs MIG Spool Gun
|Welding Aluminum TIG vs MIG Spool Gun
Welding Aluminum and Comparing TIG to Mig using a spool gun.
Part 2 of the Aluminum Awning project is Not quite ready yet but I thought it would be interesting to compare some Spool gun welds to Tig welds.
I support these videos from sales from my store at weldmongerstore.com. Check it out for TIG Fingers, shirts, DVDs, and welding accessories. Below are some products that I don’t carry, but I use them in my videos and can vouch for their quality.
WELDING MACHINES
Lincoln Viking 3350 w/4C
http://amzn.to/2rRFlUn
Lincoln Square Wave TIG 200
http://amzn.to/2rSkekZ
Lincoln Power MIG 210 MP
http://amzn.to/2s2bRnA
AHP Alpha TIG 200X
http://amzn.to/2s1XAr3
AHP Alpha 160ST
http://amzn.to/2sdK9Ed
TOOLS AND ACCESSORIES
Lincoln TIG Gloves
http://amzn.to/2sdLzyk
Metabo WE15-150 Grinder
http://amzn.to/2sB1B2U
Milwaukee Band Saw
http://amzn.to/2rymEVm
SWAG 4.0 Portaband Table
http://amzn.to/2s1FLs5
BLUE DEMON FILLER METAL
er70S2
http://amzn.to/2s1M0fP
er308L
http://amzn.to/2sBpS8U
309L
http://amzn.to/2rShLGY
er4043
http://amzn.to/2rJbrQ9
er5356
http://amzn.to/2sAQS8p
er70S2
http://amzn.to/2s1M0fP
er308L
http://amzn.to/2sBpS8U
309L
http://amzn.to/2rShLGY
er4043
http://amzn.to/2rJbrQ9
er5356
http://amzn.to/2sAQS8p
Welding Aluminum TIG vs MIG Spool Gun
Welding Aluminum TIG vs MIG Spool Gun
That mig weld penetration looks substantially more to me, and it was faster, which means it has more strength, so for me, mig looks the better choice.
What is the right amps to do the good weld tig and mig welding
fuckn hell that welder is mad i want one Lincoln are still the best welders ive ever used to this day absolutely love em great video
nonsene movies commercials
Just stumbled across this. Excellent vid! Now if I could just figure out a good machine for home use. Some days I might be welding SS exhaust pipes and other days aluminum angle… any recommendations?
угловые ,тавровые швы mig на алюминии лучше проваривает, а также меньше ведет из за большей скорости, но на стыковых полуавтомат плохо образовывает корень
This is a good example of someone who speaks clearly, videotography is also clean and includes only the subject at hand without any fumbling. The comparison and presentation leaves you with an understanding of the pros and cons so that you can make your own decision of how you want to prepare and do the job. I subscribed!!
lol.. the mig had better penetration then the tig.. iv'e had poor luck with tig welding aluminum.. very frustrating and not strong welds.. throw the spool gun on and im done in a jiffy and its stronger anyway
Hey do you read the comments i been welding 20 years /// say g/day
but can you stick it?
was blown away at how fast you went…
Nice weld !
Yey!
Hi Jody….I'm ordering my Everlast 255EXT next week along with a 60S plasma cutter. I've done all of my aluminum welding using a Millermatic 210 and a Spoolmate 3035 spool gun. It looked like the aluminum you were using for the weld test had factory edges. I've always cleaned my aluminum for MIG welding. Could the porosity shown in the cut section of the MIG welded aluminum be from the factory edges? I know the TIG didn't show the same porosity, could that simply be due to a better gas coverage? Thanks, Curt.
Hi i need to weld my exhaust together what welder should i use
Thanks sir
sigh my welds look like sh#t compared to this. But we are using a Lincoln 140 which is 110 volts and 1/8in thick aluminum which we pre-heat with a torch. Temp sweet spot is about 225 degrees, but holy crap, no way can I travel THAT fast and it certainly cannot straight pass a line, stacking dimes gives the best result. I thought my welds were looking great until I re-watched this video 😛 😱
Tig will give you much better looking welds, but the Mig will be close enough in most cases. If I have a weld that the public is going to see, I may Tig it for appearance.
Hey I really enjoyed your videos and I was wondering if you could do a review on the Vulcan Omni pro. Any advice? I’ll I’ve heard is great stuff about it. Any chance you could make a video or review? If not no big deal. Thanks.
What about wire feed tig welders?
I learned a lot from this video. I've never tried to weld aluminum with my everlast mig welder before.
Why o why, do you not – grind, file, smooth or otherwise dress welds in aluminium?
Not being sarcy I just don't know