How to hack any IR Remote using arduino.
|How to hack any IR Remote using arduino.
How to hack any IR Remote.
My remote control was not working properly recently, So I decided to make a homemade remote using Arduino. When we push a button on our remote, it sends some code to the device. It does that by rapidly blinking the IR transmitter led on our remote, we can’t see the IR Transmitter blink because it is not visible to the human eye. but a camera can catch that blink.
To find out the code that has been sent by the remote, we are going to use an IR receiver with the Arduino. After installing the IR remote library and uploading the IRrecvdemo Sketch, we can see its code in the serial monitor.
Next step would be to write a program and in the If statement of a button, we need to send those code using a send NEC function.
By this method, we can clone any IR remote we want.
Partlist:
Arduino
IR Receiver
IR Transmitter
Switch
1K and 100 Ohm Resistors
Coin Cell Battery Connector
Schematic and Code: https://goo.gl/8R9Rv1
IRremote Library: https://github.com/z3t0/Arduino-IRremote
LowPower: https://github.com/rocketscream/Low-Power
Music By : NoCopyrightSounds
Music Name : Electro-Light – Symbolish[NCD Release]
https://www.youtube.com/watch?v=__CRWE-L45k&list=LL2woEP5sdfBzEpykTGo6Qcg&index=1
? Connect with NCS
Facebook http://facebook.com/NoCopyrightSounds
Twitch http://twitch.tv/nocopyrightsounds
Twitter http://twitter.com/NCSounds
Spotify http://bit.ly/SpotifyNCS
SoundCloud http://soundcloud.com/nocopyrightsounds
Goo+ http://google.com/+nocopyrightsounds
Instagram http://instagram.com/nocopyrightsounds_
How to hack any IR Remote using arduino.
How to hack any IR Remote using arduino.
If I use uno,what modification do I need,plz help
Good i like video
Can i make this smaller with the atTiny 85?
I used the method. it does not work on my LG TV. the TV wouldn't be able to receive the signal from the ir
Hey nice video. Could you show how to connect audrino to an IR transmitter directly without the buttons ? I want to interface audrino to IR transmitter and control via mobile app rather than physical buttons.
i have no drones (T5 goolrc) remote control what can i do
can I use Attiny 85 for making only one button with IR LED….?
I want to send only one code on and off for TV and make it small so i want to use attiny 85 …..
Good video and I honestly don't mean to be rude but the audio is very difficult to hear / understand even with the volume turned up I think you have been too close to the microphone. Just I know the amount of hard work you have put into creating the video and then it being ruined by dodgy audio.
keep getting Arduino: 1.8.3 (Windows Store 1.8.6.0) (Windows 10), Board: "Arduino/Genuino Uno"
IRrecord:25: error: 'IRsend' does not name a type
IRsend irsend;
^
C:UserskomodDocumentsArduinolibrariesArduino-IRremote-masterexamplesIRrecordIRrecord.ino: In function 'void sendCode(int)':
IRrecord:109: error: 'irsend' was not declared in this scope
irsend.sendNEC(REPEAT, codeLen);
^
IRrecord:113: error: 'irsend' was not declared in this scope
irsend.sendNEC(codeValue, codeLen);
^
IRrecord:119: error: 'irsend' was not declared in this scope
irsend.sendSony(codeValue, codeLen);
^
IRrecord:124: error: 'irsend' was not declared in this scope
irsend.sendPanasonic(codeValue, codeLen);
^
IRrecord:129: error: 'irsend' was not declared in this scope
irsend.sendJVC(codeValue, codeLen, false);
^
IRrecord:144: error: 'irsend' was not declared in this scope
irsend.sendRC5(codeValue, codeLen);
^
IRrecord:147: error: 'irsend' was not declared in this scope
irsend.sendRC6(codeValue, codeLen);
^
IRrecord:154: error: 'irsend' was not declared in this scope
irsend.sendRaw(rawCodes, codeLen, 38);
^
Multiple libraries were found for "IRremote.h"
Used: C:Program FilesWindowsAppsArduinoLLC.ArduinoIDE_1.8.6.0_x64__mdqgnx93n4wttlibrariesRobotIRremote
Not used: C:UserskomodDocumentsArduinolibrariesArduino-IRremote-master
exit status 1
'IRsend' does not name a type
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
what do i do????
what type of ir sensor you used
what type of ir receiver you used
where did u set pin 3 for IR as output in ur arduino code?
i did it and smoke was produced from my Arduino Nano Atmega 328p
Could you do the same with rf.. just say you were to take the values from a garage rf remote and then made an rf transmitter from and Arduino.. is that possible?!!
Can we use 120 ohm resistor instead of 100 ohm resistor
what do i do if its sending signals but the tv is not receiving them pls reply fast
can you please provide a code for arduino?
You can add the sensor and store in EEPROM.To make it universal remote.
good job thanks mr
Good can you build a circuit of capture and record and re-transmit at the same time .
please help me i search for that circuit
A:Program filesArduinoArduinolibrariesRobotIRremotesrcIRremoteTools.cpp:5:16: error: 'TKD2' was not declared in this scope
int RECV_PIN = TKD2; // the pin the IR receiver is connected to
^
Multiple libraries were found for "IRremote.h"
Used: A:Program filesArduinoArduinolibrariesRobotIRremote
Not used: C:UsersARREONDocumentsArduinolibrariesArduino-IRremote-master
exit status 1
Error compiling for board Arduino/Genuino Uno.
I made the connections and uploaded the code but when I tried it using a button on a bread board it doesn't show the in build led .I'm using ardiuno uno
You have good knowledge .thanks
Note: your voice is so low if you can make it louder that's would be great .
can i use it for RC IR Helicopter
Yeeahh
Nice project
can we use simple 2 pic IR Reciever? if no then why?
email ?
muito boa a aula
Cool electronics video with no no no no no no no volume.I hate your voice.Really dude from outer space
Kept the sound full in my speaker and computer I cannot hear your voice
Wait are u in India and did you buy a rigol oscilloscope?! How much did you pay for the damn thing? Where fiid you buy it? Which model is it exactly?
Cool! Thanks much. Very helpful.
Brother you don't need all of those resistors you can just use the internal pull up resistor inside the Arduino.
Here is a link to show you how: https://www.arduino.cc/en/Tutorial/DigitalInputPullup
It doesnt work in Panasonic. AC.. Do you have sample sketch just for the power button?
Why you write 32 in ir.sent comment
Do you have a sample sketch for panasonic aircon .. on/off switch?
Very nice I have an IR transmitter with three buttons so would like to copy the code to make another one and it looks like you have cracked it thanks for your video
I have epson interactive pen ,can I change its IR code so it can be used with another epson interactive projector?
very good