Multiple Servo Control with Arduino Uno R3 | Arduino Tutorial
|Multiple Servo Control with Arduino Uno R3 | Arduino Tutorial
In this tutorial, we will learn how to use multi-servo with Arduino. We will control 4 servo motors with Arduino PWM outputs.You can implement your robotic arm projects with reference to this tutorial. Of course we will use external battery / power when doing this.
In the next tutorial, I’ll show you how to use multiple servos with potentiometers. Do not forget to subscribe. Thank you for your support.
I did not share the code because it is short and it varies according to the number of servos. You can write code by watching the tutorial. This is a better way to learn. I will continue to share long and complex codes.
Required Hardware
Arduino Board — https://goo.gl/UyGYeF
Servo Motor x4 — https://goo.gl/iOkPgu
Wires — https://goo.gl/VRzUN4
Breadboard — https://goo.gl/yCa8hX
Battery
Connections:
The external battery VCC / GND connect to the breadboard.
The Arduino GND connect to the breadboard’s GND input
The servo connections we use in this project are as follows;
Orange Input – Signal Input
Red Input – Power Input (VCC)
Brown Input – Ground Input(GND)
The Servo1 VCC and GND connect to the breadboard’s VCC / GND inputs
The Servo1 Signal connect to the Arduino Digital PWM 3
The Servo2 VCC and GND connect to the breadboard’s VCC / GND inputs
The Servo2 Signal connect to the Arduino Digital PWM 5
The Servo3 VCC and GND connect to the breadboard’s VCC / GND inputs
The Servo3 Signal connect to the Arduino Digital PWM 6
The Servo4 VCC and GND connect to the breadboard’s VCC / GND inputs
The Servo4 Signal connect to the Arduino Digital PWM 9
Electronics Parts – https://goo.gl/covX9J
Arduino Compatible SCM & DIY Kits – https://goo.gl/yi21yB
Arduino Modules Boards — https://goo.gl/bSCfwv
Professional Tools — https://goo.gl/9Ym9MM
Multiple Servo Control with Arduino Uno R3 | Arduino Tutorial
my first video to learn about arduino coding for servo motors 🙂 great work man.. liked and subscribed.. ☺
can i connect more servos to this please make a video adding more servos to this project
You haven't shown how the Arduino gets power. Can you explain that?
thanks,
how can I connect 2 gps modules NEO-7M to arduino?
hey where did u get that background music…Plz give that source…Thnx
what is that piece that you put in the battery called?
and where can you find it?
Hi, Where can I find the code?
Oh my goodness, you are a life saver, thank you!
Can someone tell me what would happen if I do not use common ground for arduino and servo?
you are best
could you also use a 9V battery with a jack that fits into the arduino?
How would i go about programming a sevo that can spin continiously to do so?
Thank you for sharing the video. It is a good idea that you could avoid the motor shield. Please respond.
what about 5 servos
Isn't that 9V battery? Is that OK if the servos are powered by 9V Battery?
Can you do that in the same way with the arduino pro mini?
Mert abicim simdi ben robot kol üzerinde calısıyorum ama tek bir komutla calismasini istiyorum her dakika farkli komutlar vererek calısıyor bana yardim etsen de sadece bir komutla sanki bir nesneyi alip baska bir yere koymadi gibi bir video hazırlarsan cok mutlu olurum ❤️❤️❤️
Great video! Please excuse my ignorance of the subject, but how does the 1 signal wire enable the servo motor to travel in both a clockwise and anticlockwise direction? I always thought reversing the direction of the motor required switching the polarity of the positive and negative terminals — though this is for general motors, rather than servos…. gaps in my knowledge, ah!
Any advice is very much appreciated, thank you 🙂
Wow that is awesome
nice😙😙
How do we programme the servo to work one after the other but not at the same time
The 4 servos are not working together i tried the batteries but the servos dont work the movement is very less how did you powered all of them please tell ???
Where is the code????
What is the voltage
thank's to tutorial..
wanted the code
Please give me a answer….
What a Arduino pin 1,2,4,7,8,12,13 connect with servo motor ?????
Gracias
How to write codes ?
can you please help me
hey nice bro😃😃
Do you need to have your uno plugged into the computer to control the servos or can it run just on the battery?
thanks for the video, and thanks to the mute option too
bende birisi çalıştı diğerleri çalışmıyor neden ?
Which software u use to burn coding
Electronics Parts – https://goo.gl/covX9J
Arduino Compatible SCM & DIY Kits – https://goo.gl/yi21yB
Arduino Modules Boards — https://goo.gl/bSCfwv
Professional Tools — https://goo.gl/9Ym9MM
add code links also please