How to Make Robot Hand? | Wireless Controlled with Glove | Mert Arduino and Tech

How to Make Robot Hand? | Wireless Controlled with Glove | Mert Arduino and Tech

How to Make Robot Hand – Wireless Controlled with Glove:
In this video; 3D robot hand assembly, servo control, flex sensor control, wireless control with nRF24L01, Arduino receiver and transmitter source code are available. In short, in this project we will learn how to control a robot hand with a wireless glove. The hand is part of an open-source project called InMoov. It’s a 3D-printable robot, and this is just the hand and forearm assembly.

Required Hardware:
2x Arduino Board (Nano) — http://bit.ly/2HaRyrj
2x nRF24L01+ Transceiver — http://bit.ly/2sCG7nd
2x nRF24L01+ Adapter — http://bit.ly/2soia3t
5x MG996R Servo — http://bit.ly/2kDLHlm
5x 4.5 Inch Flex Sensor — http://bit.ly/2J3hfQp
5x 10k Resistor — http://bit.ly/2xuM6jC
2x 18650 3.7V Battery — http://bit.ly/2LNZQcl
1x 18650 Battery Holder — http://bit.ly/2LihW5c
1x 9V Battery — https://goo.gl/xaD6Tf
1x 9V Battery Connector — https://goo.gl/fLjKL7
1x Glove — http://bit.ly/2xA6sYx
1x String / Braid Line — https://goo.gl/EhSdXM
3x Mini Breadboard — http://bit.ly/2J5hqL5
Jumper Wires — http://bit.ly/2J6de9E
1x Rubber / Tire or Spring
1x Steel Wire or Filament
3x Bolt ( 8mm diameter)

Required Tools (Optional):
Electronic Drill + Dremel Tool — http://bit.ly/2Li7NFF
Anet A8 3D Printer — http://bit.ly/2J18Ahn
PLA 22M Red Filament — https://goo.gl/35MSfn
Hot Glue Gun — https://goo.gl/2znyr6
Cable Ties — https://goo.gl/8FbDzU
Super Fast Adhesive — https://goo.gl/aGnizS
DANIU Screwdriver Wallet Set — https://goo.gl/i75Au5
DANIU Adjustable Solder — https://goo.gl/2oZhtu
DANIU Soldering Stand — https://goo.gl/2n8gds
DANIU Solder Wire — https://goo.gl/FC7W6o
DANIU Heat Shrink Tube — https://goo.gl/j2xcVf
DANIU Wire Cable Cutter — https://goo.gl/b96G4X
PCB Board — https://goo.gl/D1so5j
Screws Nuts Assortment Kit —https://goo.gl/EzxHyj
————————————————————————-

Thanks to InMoov — http://inmoov.fr/

For more information, visit the official InMoov website. You can visit the “Assembly Sketches” and “Assembly Help” pages in the InMoov website for more details on assembly.

All 3D parts used in this project — https://goo.gl/npCuQd

Source Code Link — https://goo.gl/c6Ugn6

RF24.h Library Link — https://github.com/maniacbug/RF24

Free Subscribe for Support — http://bit.ly/MertArduino
————————————————————————-

Background Music:
Song: Fredji – Flying High (Vlog No Copyright Music)
Video Link: https://youtu.be/ueOi5slIU2E
Song: Fredji – Happy Life (Vlog No Copyright Music)
Video Link: https://youtu.be/KzQiRABVARk
Music provided by Vlog No Copyright Music.
Mert Arduino and Tech
How to Make Robot Hand? | Wireless Controlled with Glove | Mert Arduino and Tech



How to Make Robot Hand? | Wireless Controlled with Glove | Mert Arduino and Tech

41 Comments

Add a Comment

Alamat email Anda tidak akan dipublikasikan. Ruas yang wajib ditandai *